[May 2018] 2018 Latest Updated 300-206 Dumps Free Download In Lead2pass 315q

2018 Cisco 300-206 Dumps Free Download 100% Pass Promised By Lead2pass:

https://www.lead2pass.com/300-206.html

QUESTION 31
Where in the Cisco ASA appliance CLI are Active/Active Failover configuration parameters configured?

A.    admin context
B.    customer context
C.    system execution space
D.    within the system execution space and admin context
E.    within each customer context and admin context Read More

[May 2018] 100% Free Lead2pass 300-180 New Questions Download 374q

100% New Updated 300-180 New Questions Lead2pass Helps Pass 300-180 Exam Successfully:

https://www.lead2pass.com/300-180.html

QUESTION 81
For a KVM session to be successful, which two of these need to be done? (Choose two.)

A.    The Cisco IMC IP address needs to be assigned on the Admin tab.
B.    The Cisco IMC IP address needs to be in the same subnet as the management IP.
C.    The Cisco IMC needs to be upgraded to the same version as the UCS Manager.
D.    The server needs to be fully discovered.

Answer: AD

QUESTION 82
A customer is configuring SAN pin groups in a Cisco UCS domain.
The customer notices that pinning is not working and traffic from the vHBA is not passing over the Fibre Channel uplink port. Which of these must be done for pinning to work correctly?

A.    Include the SAN pin group in a vHBA policy and then include the vHBA policy in the service profile
that is assigned to that server.
B.    Include the SAN policy in the Cisco UCS Manager to match with pin groups on the fabric interconnect.
C.    The customer must have Cisco UCS Manager version 2.0 or above.
D.    Fibre Channel switch mode needs to be configured first.

Answer: A

QUESTION 83
Refer to exhibit. A Cisco UCS admin is troubleshooting an issue with a vNIC not coming up on a blade. When looking at the CLI of the “Fabric Interconnect”,the admin runs this command to view the status of the interface.
Which option describes a possible reason why the interface is stuck in an “initializing” state?

831

A.    The service profile is not applied to a blade.
B.    The VLANs defined on the vNIC are not defined on a matching uplink port.
C.    The uplink port is down.
D.    The QoS policy on the vNIC is invalid.
E.    The MTU on the vNIC is higher than the MTU configured in the QoS system class.

Answer: C

QUESTION 84
Which two options are causes for failure of a Cisco C-Series server that is configured to boot from SAN? (Choose two.)

A.    The boot LUN ID is not 0.
B.    The ISCSI target is only available via one via one path through the network.
C.    C-Series does not support boot from SAN.
D.    The KVM dongle is attached to the front of the server with a USB stick installed.
E.    Under the FCoE properties on the vNIC adapter, the FCoE VLAN ID is set to 10.
F.    The boot table for fc0 has not been configured.

Answer: DF

QUESTION 85
Which command on the Fabric Interconnect displays packet statistics for a given QoS group and MTU size?

A.    show policy-map interface ethernet x/y
B.    show queuing interface ethernet x/y
C.    show interface ethernet x/y
D.    show class-map type qos
E.    show interface queuing ethernet x/y

Answer: B

QUESTION 86
A Cisco UCS admin is trying to integrate Cisco UCS Manager with Active Directory Authentication. After the configuration is done, the admin is still unable to log in using LDAP credentials. When running a debug on the Fabric Interconnect, this error is displayed:

ldap_build_roles_and_locales_from_attr: No attr for usr profile

Which step was missed in the configuration?

A.    The LDAP provider was not configured correctly.
B.    The proper RBAC role(s) were not assigned to the user.
C.    Cisco UCS Manager 2.1 is required for LDAP integration.
D.    The “Attribute” field in Cisco UCS was left blank.

Answer: B

QUESTION 87
Which three requirements are needed to configure a blade to boot successfully from Fibre Channel? (Choose three.)

A.    zoning
B.    LUN masking
C.    WWPN device alias
D.    boot from SAN policy
E.    SAN connectivity policy
F.    port assignment
G.    target WWPN needs to be set in the boot from SAN policy

Answer: ABD

QUESTION 88
Which description of a core file is true?

A.    It is generated by a system failure.
B.    It is generated by a process failure.
C.    It is generated by a component failure.
D.    It is generated by a hardware failure.

Answer: B

QUESTION 89
Which logs are used to troubleshoot hardware failure?

A.    system event log
B.    audit log
C.    accounting log
D.    gateway logs
E.    system log

Answer: A

QUESTION 90
A UCS Admin is trying to launch the KVM console but it is failing to launch. All IP Pools for mgmt are configured and the CIMC has an address in UCSM. They SSH to the fabric Interconnect and run an ethanalyzer while issuing a ping from their local PC to the KVM IP address. The ping is successful but they do not see the ICMP requests and replies displayed in the capture. Here is the filter they used:

FIA(nxos)# ethanalyzer local interface mgmt display-filter icmp limit-captured-frames 0

What could be the reason pings are not seen in the capture and the KVM is failing to load?

A.    Java settings are preventing the KVM from loading
B.    There is a duplicate IP address for that CIMC address
C.    The switch upstream from the FI has the wrong vlan configured
D.    The CIMC IP pool is in the same subnet as the Fabric Interconnects mgmt 0 interface

Answer: B

300-180 dumps full version (PDF&VCE): https://www.lead2pass.com/300-180.html

Large amount of free 300-180 exam questions on Google Drive: https://drive.google.com/open?id=108Bd0NBc2wWwiFC-bUg8eLE5zS0n9gVN

You may also need:

300-165 exam dumps: https://drive.google.com/open?id=0B3Syig5i8gpDSkhBVngxX0Z3Y0k

300-170 exam dumps: https://drive.google.com/open?id=0B3Syig5i8gpDdHhmcTBIbGM4bmc

300-175 exam dumps: https://drive.google.com/open?id=0B3Syig5i8gpDVDYyRldqb1AzenM

[May 2018] 100% Pass 300-135 Exam By Training Lead2pass New VCE And PDF Dumps 195q

100% Pass Lead2pass 300-135 New Questions Free Version:

https://www.lead2pass.com/300-135.html

QUESTION 41
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, and FHRP services, a trouble ticket has been operated indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to Isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?

A.    R1
B.    R2
C.    R3
D.    R4
E.    DSW1
F.    DSW2
G.    ASW1
H.    ASW2 Read More

[May 2018] Free Updated Lead2pass 300-115 Exam Dumps Download 684q

Lead2pass 100% Valid 300-115 Exam Questions PDF Free Download:

https://www.lead2pass.com/300-115.html

QUESTION 31
Which command does a network engineer use to verify the spanning-tree status for VLAN 10?

A.    switch# show spanning-tree vlan 10
B.    switch# show spanning-tree bridge
C.    switch# show spanning-tree brief
D.    switch# show spanning-tree summary
E.    switch# show spanning-tree vlan 10 brief

Read More

[May 2018] Free Lead2pass Cisco 300-101 PDF Exam Questions And Answers Download 563q

Free Lead2pass Cisco 300-101 VCE And PDF Instant Download:

https://www.lead2pass.com/300-101.html

QUESTION 21
Which statement is true about the PPP Session Phase of PPPoE?

A.    PPP options are negotiated and authentication is not performed.
Once the link setup is completed, PPPoE functions as a Layer 3 encapsulation method that allows data to be transferred over the PPP link within PPPoE headers.
B.    PPP options are not negotiated and authentication is performed.
Once the link setup is completed, PPPoE functions as a Layer 4 encapsulation method that allows data to be transferred over the PPP link within PPPoE headers.
C.    PPP options are automatically enabled and authorization is performed.
Once the link setup is completed, PPPoE functions as a Layer 2 encapsulation method that allows data to be encrypted over the PPP link within PPPoE headers.
D.    PPP options are negotiated and authentication is performed.
Once the link setup is completed, PPPoE functions as a Layer 2 encapsulation method that allows data to be transferred over the PPP link within PPPoE headers.

Answer: D
Explanation:
http://www.cisco.com/c/en/us/td/docs/security/asa/asa92/configuration/vpn/asa-vpn-cli/vpn-pppoe.html

QUESTION 22
Which type of traffic does DHCP snooping drop?

A.    discover messages
B.    DHCP messages where the source MAC and client MAC do not match
C.    traffic from a trusted DHCP server to client
D.    DHCP messages where the destination MAC and client MAC do not match

Answer: B
Explanation:
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/12-2SX/configuration/guide/book/snoodhcp.html

QUESTION 23
Refer to the exhibit. Which command only announces the 1.2.3.0/24 network out of FastEthernet 0/0?

231

A.    distribute list 1 out
B.    distribute list 1 out FastEthernet0/0
C.    distribute list 2 out
D.    distribute list 2 out FastEthernet0/0

Answer: D
Explanation:
Access list 2 is more specific, allowing only 1.2.3.0/24, whereas access list 1 permits all 1.0.0.0/8 networks. This question also asks us to apply this distribute list only to the outbound direction of the fast Ethernet 0/0 interface, so the correct command is “distribute list 2 out FastEthernet0/0.”

QUESTION 24
Which prefix is matched by the command ip prefix-list name permit 10.8.0.0/16 ge 24 le 24?

A.    10.9.1.0/24
B.    10.8.0.0/24
C.    10.8.0.0/16
D.    10.8.0.0/23

Answer: B
Explanation:
With prefix lists, the ge 24 term means greater than or equal to a /24 and the le 24 means less than or equal to /24, so only a /24 is both greater than or equal to 24 and less than or equal to 24. This translates to any prefix in the 10.8.x.0/24 network, where X is any value in the 0-255 range.
Only the choice of 10.8.0.0.24 matches this.

QUESTION 25
Router A and Router B are configured with IPv6 addressing and basic routing capabilities using OSPFv3. The networks that are advertised from Router A do not show up in Router B’s routing table. After debugging IPv6 packets, the message “not a router” is found in the output.
Why is the routing information not being learned by Router B?

A.    OSPFv3 timers were adjusted for fast convergence.
B.    The networks were not advertised properly under the OSPFv3 process.
C.    An IPv6 traffic filter is blocking the networks from being learned via the Router B interface that is connected to Router A.
D.    IPv6 unicast routing is not enabled on Router A or Router B.

Answer: D
Explanation:
http://www.cisco.com/c/en/us/td/docs/ios/ipv6/command/reference/ipv6_book/ipv6_16.html

QUESTION 26
After you review the output of the command show ipv6 interface brief, you see that several IPv6 addresses have the 16-bit hexadecimal value of “FFFE” inserted into the address.
Based on this information, what do you conclude about these IPv6 addresses?

A.    IEEE EUI-64 was implemented when assigning IPv6 addresses on the device.
B.    The addresses were misconfigured and will not function as intended.
C.    IPv6 addresses containing “FFFE” indicate that the address is reserved for multicast.
D.    The IPv6 universal/local flag (bit 7) was flipped.
E.    IPv6 unicast forwarding was enabled, but IPv6 Cisco Express Forwarding was disabled.

Answer: A
Explanation:
Extended Unique Identifier (EUI), as per RFC2373, allows a host to assign iteslf a unique 64-Bit IP Version 6 interface identify them EUI-64). This feature is a key benefit over IPv4 as it eliminates the need of manual configuration or DHCP as in the world of IPv4. The IPv6 EUI-64 format address is obtained through the 48-bit MAC address. The Mac address is first separated into two 24-bits, with one being OUI (Organizationally Unique Identifier) and the other being NIC specific. The 16-bit 0xFFFE is then inserted between these two 24-bits to for the 64-bit EUI address. IEEE has chosen FFFE as a reserved value which can only appear in EUI-64 generated from the EUI-48 MAC address.
https://supportforums.cisco.com/document/100566/understanding-ipv6-eui-64-bit-address

QUESTION 27
A packet capture log indicates that several router solicitation messages were sent from a local host on the IPv6 segment. What is the expected acknowledgment and its usage?

A.    Router acknowledgment messages will be forwarded upstream, where the DHCP server will allocate addresses to the local host.
B.    Routers on the IPv6 segment will respond with an advertisement that provides an external path from the local subnet, as well as certain data, such as prefix discovery.
C.    Duplicate Address Detection will determine if any other local host is using the same IPv6 address for communication with the IPv6 routers on the segment.
D.    All local host traffic will be redirected to the router with the lowest ICMPv6 signature, which is statically defined by the network administrator.

Answer: B
Explanation:
Router Advertisements (RA) are sent in response to router solicitation messages. Router solicitation messages, which have a value of 133 in the Type field of the ICMP packet header, are sent by hosts at system startup so that the host can immediately autoconfigure without needing to wait for the next scheduled RA message. Given that router solicitation messages are usually sent by hosts at system startup (the host does not have a configured unicast address), the source address in router solicitation messages is usually the unspecified Ipv6 address (0:0:0:0:0:0:0:0). If the host has a configured unicast address, the unicast address of the interface sending the router solicitation message is used as the source address in the message. The destination address in router solicitation messages is the all-routers multicast address with a scope of the link. When an RA is sent in response to a router solicitation, the destination address in the RA message is the unicast address of the source of the router solicitation message. RA messages typically include the following information:
One or more onlink Ipv6 prefixes that nodes on the local link can use to automatically configure their Ipv6 addresses
Lifetime information for each prefix included in the advertisement
Sets of flags that indicate the type of autoconfiguration (stateless or stateful) that can be completed
Default router information (whether the router sending the advertisement should be used as a default router and, if so, the amount of time (in seconds) the router should be used as a default router)
Additional information for hosts, such as the hop limit and MTU a host should use in packets that it originates
http://www.cisco.com/c/en/us/td/docs/ios/ipv6/configuration/guide/12_4t/ipv6_12_4t_book/ip6-addrg_bsc_con.html

QUESTION 28
A user is having issues accessing file shares on a network. The network engineer advises the user to open a web browser, input a prescribed IP address, and follow the instructions.
After doing this, the user is able to access company shares.
Which type of remote access did the engineer enable?

A.    EZVPN
B.    IPsec VPN client access
C.    VPDN client access
D.    SSL VPN client access

Answer: D
Explanation:
The Cisco AnyConnect VPN Client provides secure SSL connections to the security appliance for remote users. Without a previously installed client, remote users enter the IP address in their browser of an interface configured to accept SSL VPN connections. Unless the security appliance is configured to redirect http:// requests to https://, users must enter the URL in the form https://<address>.
After entering the URL, the browser connects to that interface and displays the login screen. If the user satisfies the login and authentication, and the security appliance identifies the user as requiring the client, it downloads the client that matches the operating system of the remote computer. After downloading, the client installs and configures itself, establishes a secure SSL connection and either remains or uninstalls itself (depending on the security appliance configuration) when the connection terminates.
http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/100936-asa8x-split-tunnel-anyconnect-config.html

QUESTION 29
Which Cisco IOS VPN technology leverages IPsec, mGRE, dynamic routing protocol, NHRP, and Cisco Express Forwarding?

A.    FlexVPN
B.    DMVPN
C.    GETVPN
D.    Cisco Easy VPN

Answer: B
Explanation:
Dynamic Multipoint Virtual Private Network (DMVPN) is a dynamic tunneling form of a virtual private network (VPN) supported on Cisco IOS-based routers and Unix-like Operating Systems based on the standard protocols, GRE, NHRP and Ipsec. This DMVPN provides the capability for creating a dynamic-mesh VPN network without having to pre-configure (static) all possible tunnel end-point peers, including Ipsec (Internet Protocol Security) and ISAKMP (Internet Security Association and Key Management Protocol) peers. DMVPN is initially configured to build out a hub-and-spoke network by statically configuring the hubs (VPN headends) on the spokes, no change in the configuration on the hub is required to accept new spokes. Using this initial hub- and-spoke network, tunnels between spokes can be dynamically built on demand (dynamic-mesh) without additional configuration on the hubs or spokes. This dynamic-mesh capability alleviates the need for any load on the hub to route data between the spoke networks.
DMVPN is combination of the following technologies:
http://en.wikipedia.org/wiki/Dynamic_Multipoint_Virtual_Private_Network

QUESTION 30
A network engineer is configuring a solution to allow failover of HSRP nodes during maintenance windows, as an alternative to powering down the active router and letting the network respond accordingly. Which action will allow for manual switching of HSRP nodes?

A.    Track the up/down state of a loopback interface and shut down this interface during maintenance.
B.    Adjust the HSRP priority without the use of preemption.
C.    Disable and enable all active interfaces on the active HSRP node.
D.    Enable HSRPv2 under global configuration, which allows for maintenance mode.

Answer: A
Explanation:
The standby track command allows you to specify another interface on the router for the HSRP process to monitor in order to alter the HSRP priority for a given group. If the line protocol of the specified interface goes down, the HSRP priority is reduced. This means that another HSRP router with higher priority can become the active router if that router has standby preempt enabled. Loopback interfaces can be tracked, so when this interface is shut down the HSRP priority for that router will be lowered and the other HSRP router will then become the active one.
http://www.cisco.com/c/en/us/support/docs/ip/hot-standby-router-protocol-hsrp/13780-6.html

300-101 dumps full version (PDF&VCE): https://www.lead2pass.com/300-101.html

Large amount of free 300-101 exam questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDbHBiVVk1ZVhpOGc

You may also need:

300-115 exam dumps: https://drive.google.com/open?id=0B3Syig5i8gpDM0pqaFJWUXVuM2M

300-135 exam dumps: https://drive.google.com/open?id=0B3Syig5i8gpDZmFQVlZDZnpLejA

[May 2018] Free Lead2pass Cisco 300-075 PDF Exam Questions And Answers Download 423q

Free Lead2pass Cisco 300-075 VCE And PDF Instant Download:

https://www.lead2pass.com/300-075.html

QUESTION 41
Cisco Unified Communications Manager is configured with CAC for a maximum of 10 voice calls.
Which action routes the 11th call through the PSTN?

A.    Configure an SIP trunk to the ISR.
B.    Configure Cisco Unified Communications Manager AAR.
C.    Configure Cisco Unified Communications Manager RSVP-enabled locations.
D.    Configure Cisco Unified Communications Manager locations.

Read More