Latest 2014 Pass4sure and Lead2pass Cisco 200-120 Dumps (81-90)

QUESTION 81
What is a global command?

A.    a command that is set once and affects the entire router
B.    a command that is implemented in all foreign and domestic IOS versions
C.    a command that is universal in application and supports all protocols
D.    a command that is available in every release of IOS, regardless of the version or deployment status
E.    a command that can be entered in any configuration mode

Answer: A
Explanation:
When you enter global configuration mode and enter a command, it is applied to the running configuration file that is currently running in ram. The configuration of a global command affects the entire router. An example of a global command is one used for the hostname of the router.

QUESTION 82
Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used?

A.    hop count
B.    administrative distance
C.    link bandwidth
D.    link delay
E.    link cost

Answer: B
Explanation:
By default the administrative distance of a static route is 1, meaning it will be preferred over all dynamic routing protocols. If you want to have the dynamic routing protocol used and have the static route be used only as a backup, you need to increase the AD of the static route so that it is higher than the dynamic routing protocol.

QUESTION 83
Before installing a new, upgraded version of the IOS, what should be checked on the router, and which command should be used to gather this information? (Choose two.)

A.    the amount of available ROM
B.    the amount of available flash and RAM memory
C.    the version of the bootstrap software present on the router
D.    show version
E.    show processes
F.    show running-config

Answer: BD
Explanation:
When upgrading new version of the IOS we need to copy the IOS to the Flash so first we have to check if the Flash has enough memory or not. Also running the new IOS may require more RAM than the older one so we should check the available RAM too. We can check both with the “show version” command.

QUESTION 84
Which command would you use on a Cisco router to verify the Layer 3 path to a host?

A.    tracert address
B.    traceroute address
C.    telnet address
D.    ssh address

Answer: B
Explanation:
In computing, traceroute is a computer network diagnostic tool for displaying the route (path) and
measuring transit delays of packets across an Internet Protocol (IP) network. The history of the route is recorded as the round-trip times of the packets received from each successive host (remote node) in the route (path); the sum of the mean times in each hop indicates the total time spent to establish the connection. Traceroute proceeds unless all (three) sent packets are lost more than twice, then the connection is lost and the route cannot be evaluated. Ping, on the other hand, only computes the final round-trip times from the destination point.

QUESTION 85
What information does a router running a link-state protocol use to build and maintain its topological database? (Choose two.)

A.    hello packets
B.    SAP messages sent by other routers
C.    LSAs from other routers
D.    beacons received on point-to-point links
E.    routing tables received from other link-state routers
F.    TTL packets from designated routers

Answer: AC
Explanation:
Neighbor discovery is the first step in getting a link state environment up and running. In keeping with the friendly neighbor terminology, a Hello protocol is used for this step. The protocol will define a Hello packet format and a procedure for exchanging the packets and processing the information the packets contain.
After the adjacencies are established, the routers may begin sending out LSAs. As the term flooding implies, the advertisements are sent to every neighbor. In turn, each received LSA is copied and forwarded to every neighbor except the one that sent the LSA.

QUESTION 86
Which statements describe the routing protocol OSPF? (Choose three.)

A.    It supports VLSM.
B.    It is used to route between autonomous systems.
C.    It confines network instability to one area of the network.
D.    It increases routing overhead on the network.
E.    It allows extensive control of routing updates.
F.    It is simpler to configure than RIP v2.

Answer: ACE
Explanation:
The OSPF protocol is based on link-state technology, which is a departure from the Bellman-Ford vector based algorithms used in traditional Internet routing protocols such as RIP. OSPF has introduced new concepts such as authentication of routing updates, Variable Length Subnet Masks (VLSM), route summarization, and so forth.
OSPF uses flooding to exchange link-state updates between routers. Any change in routing information is flooded to all routers in the network. Areas are introduced to put a boundary on the explosion of link-state updates. Flooding and calculation of the Dijkstra algorithm on a router is limited to changes within an area.

QUESTION 87
What is the default administrative distance of OSPF?

A.    90
B.    100
C.    110
D.    120

Answer: C
Explanation:
Administrative distance is the feature that routers use in order to select the best path when there are two or more different routes to the same destination from two different routing protocols. Administrative distance defines the reliability of a routing protocol. Each routing protocol is prioritized in order of most to least reliable (believable) with the help of an administrative distance value.
Default Distance Value Table
This table lists the administrative distance default values of the protocols that Cisco supports:
Route Source
Default Distance Values
Connected interface
Static route
Enhanced Interior Gateway Routing Protocol (EIGRP) summary route External Border Gateway Protocol (BGP)
Internal EIGRP
IGRP
OSPF
Intermediate System-to-Intermediate System (IS-IS)
Routing Information Protocol (RIP)
Exterior Gateway Protocol (EGP)
On Demand Routing (ODR)
External EIGRP
Internal BGP
Unknown*

QUESTION 88
Which characteristics are representative of a link-state routing protocol? (Choose three.)

A.    provides common view of entire topology
B.    exchanges routing tables with neighbors
C.    calculates shortest path
D.    utilizes event-triggered updates
E.    utilizes frequent periodic updates

Answer: ACD
Explanation:
Each of routers running link-state routing protocol learns paths to all the destinations in its “area” so we can say although it is a bit unclear.
Link-state routing protocols generate routing updates only (not the whole routing table) when a change occurs in the network topology so
Link-state routing protocol like OSPF uses Dijkstra algorithm to calculate the shortest path -> . Unlike Distance vector routing protocol (which utilizes frequent periodic updates), link-state routing protocol utilizes event-triggered updates (only sends update when a change occurs) ->

QUESTION 89
Which command would you configure globally on a Cisco router that would allow you to view directly connected Cisco devices?

A.    enable cdp
B.    cdp enable
C.    cdp run
D.    run cdp

Answer: C
Explanation:
CDP is enabled on Cisco routers by default. If you prefer not to use the CDP capability, disable it with the no cdp run command. In order to reenable CDP, use the cdp run command in global configuration mode. The “cdp enable” command is an interface command, not global.

QUESTION 90
Which two locations can be configured as a source for the IOS image in the boot system command? (Choose two.)

A.    RAM
B.    NVRAM
C.    flash memory
D.    HTTP server
E.    TFTP server
F.    Telnet server

Answer: CE
Explanation:
The following locations can be configured as a source for the IOS image:
1. + Flash (the default location)
2. + TFTP server
3. + ROM (used if no other source is found)

If you want to pass Cisco 200-120 successfully, donot missing to read latest lead2pass Cisco 200-120 practice tests.
If you can master all lead2pass questions you will able to pass 100% guaranteed.

http://www.lead2pass.com/200-120.html